Template:SIM7600CE-4G-HAT Manual

Testing

Hardware setting

• This module comes with GSM antenna, LTE antenna and micro USB cable. Besides these you should prepare:
  • A 4G sim card
  • A microphone cable
  • A Micro SD card (Optional)
• Insert the SIM card to the card slot, Insert the headphone cable and connect the LTE antenna.
  

• 

  back side
• 

  front size

• Connect the USB interface of SIM7600E-H 4G HAT to PC with a micro USB cable. Then the PWR indicator will keep bright.
• Press the PWRKEY button and hold for 1s, the NET indicator will blink 1 time per second.
• Open Device Manager to check the COM ports
  
• Install SIM7600 driver(driver)

【Note】The default hardware of SIM7600CE 4G HAT needs to be turned on by button. If the hardware needs to be turned on automatically, you can use a connection line to connect the PWR and GND pins on the module pin, so that it can automatically turn on, as shown in the figure below

Testing it with AT commands

General AT commands

Command	Description	Return
AT	AT test command	OK
ATE	ATE1: Enable echo ATE0: Disable echo	OK
AT+CGMI	Module manufacturers	OK
AT+CGMM	Module model	OK
AT+CGSN	Serial number	OK
AT+CSUB	Module revision	OK
AT+CGMR	Firmware revision	OK
AT+IPREX	Set baud rate	+IPREX: OK
AT+CRESET	Reset module	OK
AT+CSQ	Check signal quality	+CSQ: 17,99 OK
AT+CPIN?	SIM Card Status	+CPIN: READY
AT+COPS?	Operator selection	+COPS: OK
AT+CREG?	Network registration	+CREG: OK
AT+CPSI?	UE system infor
AT+CNMP	Mode selection: 2：Automatic 13：GSM only 38：LTE only 48 ： Any modes but LTE ... ....	OK

For more details, please refer to the documentation: SIM7500_SIM7600 Series_AT Command Manual_V1.07

Raspbian networking by 4G

• Insert the module to 40PIN GPIO of Raspberry Pi, connect the USB interface of 4G module to USB port of Pi, and start it.：

• Initailize Raspberry Pi according to “[[#Initailize Raspberry Pi | Initailize Raspberry Pi]”
• Refer to the guide below for networking.(Recommand you use USB port for faster speed):
  • #Networkigng via wwan0 Interface
    
• If the network work abnormally, please check set the DNS by commands below for a try:

route add -net 0.0.0.0 ppp0

Test GPS

• Connecting the GPS antenna, and place the receiver on open area outdoor
• AT Commands used

AT+CGPS=1	    //Enable GPS
AT+CGPSINFO       //Print GPS information to serial port
AT+CGPS=0       //Disable GPS

TCP/IP Connection

Please make sure that your SIM card supports GPRS services.

1. Assemble the SIM card, connect all the antenna, and connect the module to PC by USB cable.
2. Press the PWR button to power on the module and wait for a dozen seconds.
3. Mkae sure that all the indicator light normally.

Set the local virtual servers settings

Virtual servers define the mapping between service ports of WAN and web servers of LAN. All requests from the Internet to service ports of WAN will be redirected to the computer (webservers of LAN) specified by the server IP. (see your router’s guide manual)）

1. Log in Management Console of your router with a browser (read your router’s guide manual for specific address)
2. Set Port：：2317（The Port can’t conflict to others. Here we set2317）
3. Set LAN IP address of your computer (you can run CMD on your computer, and execute commands config to inquiry the address of IPv4), 192.168.1.168 as examples
   

Get WAN IP

You can search “IP” on the browser to get your WAN IP address

Set GPRS

AT+CGDCONT=1,"IP","CMNET"     //Set APN
AT+CSQ       //Check the quality of the signal, bigger the value, stronger the signal.
AT+CREG?         //GPRS network status
AT+CIPMODE=1        //TCP/IP mode
AT+CSOCKSETPN=1          //PDP profile number
AT+CIPMODE=0          //Choose TCP/IP mode
AT+NETOPEN         //Open socket
AT+CIPOPEN=0,"TCP","113.81.233.65",2317         //establish connection
AT+CIPSEND=0,9，         //Send data of a specific size
1A                     //(HEX format) Tell module to send data
AT+CIPCLOSE=0，         //close connection
AT+NETCLOSE，         //Close socket

Test TF card

1. Plug the SIM card, connect the LTE antenna, and connect the USB interface of SIM7600E-H 4G HAT to PC. Then press the PWRKEY to power on

2. User command to use TF card

AT+FSCD=D:				//Choose the path of TF card 
+FSCD: D:/
OK
AT+FSLS					//Check subdirecotry
+FSLS: SUBDIRECTORIES: 
overlays
MyDir
System Volume Information
...
...
OK

</ br> 3. Create file and write data to TF card Create MyDir folder in the root directory and create tx.txt in the folder, write data test content to the file by the following commands

AT+CFTRANRX="D:/MyDir/t1.txt",12				//file name
>test content								//data
OK

4. Open file of TF card

AT+CFTRANTX="D:/MyDir/t1.txt"
+CFTRANTX: DATA,012
test content
+CFTRANTX: 0
OK

</ br>

For more information about the commands, please refer to SIM7500_SIM7600 Series_AT Command Manual_V1.07 P256~P268

Take calls

• Connect the hardware and power on the SIM7600X module.
• Commands for taking calls：
  

AT+CNUM	Phone number (Not all SIM cards Support)	+CNUM OK
AT+CSDVC	AT+CSDVC=1：Handset output AT+CSDVC=3：Speaker output	OK
AT+CLVL=?	check volume level	OK
AT+CLVL=2	volume level set to 2	OK
ATD<phone_number>;	Make calls	OK
AT+CHUP	Hang up call	OK
AT+CLIP=1	Phone ring	OK
ATA	Answer call	OK

【Note】: You need to check "new line" when using SSCOM to test

Send/Receive SMS

1. Plug the SIM card, connect the LTE antenna and connect the USB interface of SIM7600E-H 4G HAT to PC. Then press the PWRKEY to
2. Check whether the indicators blink correctly (PWR’s and NET’s flashes).
3. Use commands below to send SMS

Comamnd	Description	Return
AT+CMGF=1	select message format	OK
AT+CSCS="GSM"	Select TE character set: GSM	OK
AT+CSMP	set text mode para	OK
AT+CMGS="<phonenumber>"	Send message	OK
AT+CNMI=2,1	message indications	OK
AT+CMGR=1	Read message 1	OK

Working with Raspberry Pi

Hardware connection

The relationship between SIM7600 control pins and Raspberry Pi IOs is shown in Table：

SIM7600X 4G HAT	Raspberry Pi
5V	5V
GND	GND
RXD	TXD (BCM: 14)
TXD	RXD (BCM: 15)
PWR	P22 (BCM: P6)
FLIGHTMODE	P7 (BCM: P4), high active

Initialize Raspberry Pi

You need to set the SIM7600 module to the working mode first.

• Download demo codesdemo codes，unzip it and recommend the folder Rspberry Pi/c as SIM7600X，and sopy it to /home/pi directory of Raspberry Pi
• Go to /home/pi/SIM7600X directory and run the following command.

chmod 777 sim7600_4G_hat_init

• Set auto-run when booting:

sudo nano /etc/rc.local

• Add the line below in the from of exit 0：

sh /home/pi/SIM7600X/sim7600_4G_hat_init

Enable serial port

For proper use, you need to disable the login shell and enable the hardware serial.

sudo raspi-config

Choose Interfacing Options ->Serial ->no -> yes，

Networking via wwan0 Interface

1、Connect the USB interface of SIM7600 module to Rasberry Pi by USB cable

2、Use ifconfig command to check wwan0 interface.

3、Install libqmi and udhcpc

sudo apt-get install libqmi-utils udhcpc -y

3、Check the status of wwan0 interface：

sudo qmicli -d /dev/cdc-wdm0 --dms-get-operating-mode

If the status is not online, you need to run the following command to configure it and test again.

sudo qmicli -d /dev/cdc-wdm0 --dms-set-operating-mode='online'

4、Set wwan0 network

sudo qmicli -d /dev/cdc-wdm0 -w	
sudo ip link set wwan0 down	
sudo echo 'Y' | sudo tee /sys/class/net/wwan0/qmi/raw_ip
sudo ip link set wwan0 up

5、 Set APN and connect to network.

sudo qmicli -p -d /dev/cdc-wdm0 --device-open-net='net-raw-ip|net-no-qos-header' --wds-start-network="apn='YOUR_APN',username='YOUR_USERNAME',password='YOUR_PASSWORD',ip-type=4" --client-no-release-cid

Note: the apn, username, password and other parameters should be modified according to the actual situation.

The user name of APN can be ignore sometimes. For examples:

sudo qmicli -p -d /dev/cdc-wdm0 --device-open-net='net-raw-ip|net-no-qos-header' --wds-start-network="apn='CMNET',ip-type=4" --client-no-release-cid

6、User udhcpc to set router and IP

 sudo udhcpc -i wwan0

7、Now you can disconnect the RJ45, turn off the WiFi and test the 4G network.

Minicom test

1、Connect the SIM7600 module and power on Raspberry Pi
2、Install minicom

sudo apt-get install minicom

3、Use the command minicom -D /dev/ttyS0 for testing
Default baud rate: 115200
If you use Pi2B/zero, the serial port should be ttyAMA0
4、Send commands:

Demo codes

1、Connect the SIM7600 module and power on Raspberry Pi
2、Dwonalod demo codes and copy it to /home/pi/ directory；

wget http://47.107.148.244/w/images/2/29/SIM7600X-4G-HAT-Demo.7z
sudo apt-get install p7zip-full
7z x SIM7600X-4G-HAT-Demo.7z   -r -o/home/pi
sudo chmod 777 -R /home/pi/SIM7600X-4G-HAT-Demo

3、Enter the folder of bcm2835 compile and install BCM2835 libraries：

chmod +x configure && ./configure && sudo make && sudo make install

4、Enter the examples folder and run the codes as below：

sudo make clean      //Clean
sudo make        //compile 
sudo ./PhoneCall       //run the codes

You can also combine the commands：

sudo make clean && sudo make && sudo ./PhoneCall

PHONECALL example

SMS example

GPS example

TCP example

FTP example

Arduino example

Hardware connection

Connect the SIM7600 module to UNO PLUS / Arduino UNO：

SIM7600X 4G HAT	UNO PLUS / Arduino UNO
5V	5V
GND	GND
TXD	0 (RX)
RXD	1 (TX)
PWR	2

Install Arduino Libraries

Downloaad the demo codes and unzip it
Copy folder Waveshare_SIM7600X_Arduino_Library to libraries folder under the installation directory of Arduino IDE
Open Arduino IDE --> File -->Examples -->Waveshare SIM7600X，and run the examples：

Examples

PHONECALL example

SMS example

GPS example

TCP example

FTP example

Jetson Nano Examples

Hardware connection

Jetson Nano has the same 40PIN header as Raspberry Pi.

connection

SIM7600X 4G HAT	Jetson Nano
5V	5V
GND	GND
TXD	10 (Board)
RXD	8 (Board)
PWR	31(Board)

Jetson Nano minicom test

1、Connect SIM7600X 4G HAT to Jetson Nano and power on it by pressing the PWRKERY key for 3s.将SIM7600X 4G HAT接入Jetson Nano中，按下PWRKER键三秒后开机
2、Access Jetson nano
3、Open a terminal and install minicom：

sudo apt-get install minicom

3、use the command to test module

sudo minicom -D /dev/ttyTHS1 -b 115200

4、 Send commands:

Python Examples

Install libraries

sudo apt-get python3-pip
sudo pip3 install pyserial
sudo apt-get install p7zip

Download the demo codes

mkdir -p ~/Documents/SIM7600X_4G_HAT
wget -P ~/Documents/SIM7600X_4G_HAT/ http://47.107.148.244/w/images/2/29/SIM7600X-4G-HAT-Demo.7z

Ener the folder of demo codes and unzip it

cd ~/Documents/SIM7600X_4G_HAT/
sudo p7zip --uncompress SIM7600X-4G-HAT-Demo.7z

AT

Connect the SIM7600X_4G_HAT to Jetson Nano.</ br> Enter the directoryJetson Nano/AT：

cd ~/Documents/SIM7600X_4G_HAT/Jetson\ nano/AT/
sudo python3 AT.py

GPS

Connect the SIM7600X_4G_HAT to Jetson Nano.</ br> Enter the directory Jetson Nano/GPS：

cd ~/Documents/SIM7600X_4G_HAT/Jetson\ nano/GPS/
sudo python3 GPS.py

PhoneCall

Connect the SIM7600X_4G_HAT to Jetson Nano.</ br> Enter the direcoryJetson Nano/PhoneCall：

cd ~/Documents/SIM7600X_4G_HAT/Jetson\ nano/PhoneCall/
sudo python3 PhoneCall.py

Note: You need to modify the number by modify the codes.

SMS

Connect the SIM7600X_4G_HAT to Jetson Nano.</ br>
Enter the directory Jetson Nano/SMS：

cd ~/Documents/SIM7600X_4G_HAT/Jetson\ nano/SMS/
sudo python3 SMS.py

Note: You need to change the phone number by modify the codes

TCP

Connect the SIM7600X_4G_HAT to Jetson Nano.</ br>。
Enter the directory Jetson Nano/TCP：

cd ~/Documents/SIM7600X_4G_HAT/Jetson\ nano/TCP/
sudo python3 TCP.py

Note: you need to modify the address to the actual one.