Difference between revisions of "2.13inch e-Paper HAT"
(创建页面，内容为“==产品介绍== 这是一款2.13inch电子墨水屏显示模块， 分辨率为250x122, 支持黑白两色刷新， 通信接口为SPI接口。 ==特点== *尺寸…”) |
m (Text replacement - "47.107.148.244" to "{{SERVERNAME}}") |
||
| (6 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | == | + | ==Introduction== |
| − | + | This is 2.13inch e-Paper module, 250x122 resolution, SPI interface, supports black and white colors. | |
| − | == | + | ==Features== |
| − | * | + | *Size： 2.13 inch |
| − | * | + | *Dimension（Raw panel）：59.2mm × 29.2mm × 1.05mm |
| − | * | + | *Dimension（PCBA）：65mmx30.2mm |
| − | * | + | *Display area：48.55mm × 23.71mm |
| − | * | + | *Operating voltage：3.3V/5V |
| − | * | + | *Interface：SPI |
| − | * | + | *Pitch：0.194* 0.194 |
| − | * | + | *Resolution：250*122 |
| − | * | + | *Display colors：Black, White |
| − | * | + | *Gray scale：2 |
| − | * | + | *Partial update ：0.3s |
| − | * | + | *Fully update ：2s |
| − | * | + | *Consumption (refresh) ： 26.4mW(typ.) |
| − | * | + | *Consumption (standby) ：<=0.017mW |
| − | + | 【Notices】： | |
| − | + | Update time: The data provided is for reference, the actual time may be different according to the MCU. The e-Paper will flicker when updating, it is normal<br /> | |
| − | + | Consumption: The data provided is for reference, the actual consumption may be different according to the driver board.<br /> | |
| − | ==SPI | + | ==SPI timing== |
[[File:e-paper-spi-timing.jpg|700px]] | [[File:e-paper-spi-timing.jpg|700px]] | ||
| − | + | The e-Paper only supports writing, therefore the MISO pin is hidden. | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | == | + | CS is slave chip select, when CS is low, the chip is enabled.<br /> |
| − | === | + | DC is data/command control pin, when DC = 0, write command, when DC = 1, write data.<br /> |
| − | + | SCLK is the SPI communication clock.<br /> | |
| − | + | SDIN is the data line from the master to the slave in SPI communication.<br /> | |
| − | + | Timing：CPHL=0， CPOL=0 （SPI0）<br /> | |
| − | * | + | 【Note】You can search more documents of SPI bus online. |
| − | * | + | |
| + | ==Working protocol== | ||
| + | ===Pixel & Byte=== | ||
| + | We define the pixels in a monochrome picture, 0 is black and 1 is white.<br /> | ||
| + | White：□，Bit 1<br /> | ||
| + | Black：■：Bit 0<br /> | ||
| + | *The dot in the figure is called a pixel. As we know, 1 and 0 are used to define the color, therefore we can use one bit to define the color of one pixel, and 1 byte = 8pixels<br /> | ||
| + | *For example, If we set first 8 pixels to black and the last 8 pixels to white, we show it by codes, they will be 16 bit as below:<br /> | ||
[[file:e-paper_hardware_work_1.png]]<br /> | [[file:e-paper_hardware_work_1.png]]<br /> | ||
| − | + | For computer, the data is saved in MSB format:<br /> | |
[[file:e-paper_hardware_work_2.png]]<br /> | [[file:e-paper_hardware_work_2.png]]<br /> | ||
| − | + | So we can use two bytes for 16 pixels.<br /> | |
| − | + | ==User Guides== | |
| − | + | *[[E-paper for RPi Use|Raspberry Pi User Guide]] | |
| − | + | *[[E-paper for Jetsonnano Use|Jetson Nano User Guide]] | |
| − | + | *[[E-paper for STM32 Use|STM32 User Guide]] | |
| − | == | + | *[[E-paper for Arduino Use|Arduino User Guide]] |
| − | |||
| − | *[ | ||
| − | *[[E- | ||
| − | |||
| − | === | + | ==Resources== |
| + | ===Document=== | ||
| + | *[http://{{SERVERNAME}}/w/images/5/57/2.13inch_e-Paper_HAT_Schematic.pdf Schematic]<br> | ||
| + | ===Demo codes=== | ||
| + | *[http://{{SERVERNAME}}/w/images/5/50/E-Paper.7z Demo codes] | ||
| − | ===开发资料=== | + | ===Datasheet=== |
| + | *[http://{{SERVERNAME}}/w/images/e/e6/2.13inch_e-Paper_Datasheet.pdf 2.13inch e-Paper Datasheet] | ||
| + | <!-- ===开发资料=== --> | ||
==FAQ== | ==FAQ== | ||
| − | |||
{{E-Paper FAQ}} | {{E-Paper FAQ}} | ||
Latest revision as of 11:32, 11 July 2020
Contents
Introduction
This is 2.13inch e-Paper module, 250x122 resolution, SPI interface, supports black and white colors.
Features
- Size： 2.13 inch
- Dimension（Raw panel）：59.2mm × 29.2mm × 1.05mm
- Dimension（PCBA）：65mmx30.2mm
- Display area：48.55mm × 23.71mm
- Operating voltage：3.3V/5V
- Interface：SPI
- Pitch：0.194* 0.194
- Resolution：250*122
- Display colors：Black, White
- Gray scale：2
- Partial update ：0.3s
- Fully update ：2s
- Consumption (refresh) ： 26.4mW(typ.)
- Consumption (standby) ：<=0.017mW
【Notices】：
Update time: The data provided is for reference, the actual time may be different according to the MCU. The e-Paper will flicker when updating, it is normal
Consumption: The data provided is for reference, the actual consumption may be different according to the driver board.
SPI timing
The e-Paper only supports writing, therefore the MISO pin is hidden.
CS is slave chip select, when CS is low, the chip is enabled.
DC is data/command control pin, when DC = 0, write command, when DC = 1, write data.
SCLK is the SPI communication clock.
SDIN is the data line from the master to the slave in SPI communication.
Timing：CPHL=0， CPOL=0 （SPI0）
【Note】You can search more documents of SPI bus online.
Working protocol
Pixel & Byte
We define the pixels in a monochrome picture, 0 is black and 1 is white.
White：□，Bit 1
Black：■：Bit 0
- The dot in the figure is called a pixel. As we know, 1 and 0 are used to define the color, therefore we can use one bit to define the color of one pixel, and 1 byte = 8pixels
- For example, If we set first 8 pixels to black and the last 8 pixels to white, we show it by codes, they will be 16 bit as below:
For computer, the data is saved in MSB format:
So we can use two bytes for 16 pixels.
User Guides
Resources
Document
Demo codes
Datasheet
FAQ
1、Working requirements of e-Paper?|
- 【Working】Temperature: 0~50°C; Humidity: 35%~65%RH
- 【Storage】Temperature: ≤30°C; Humidity: ≤55%RH; Max storage time: 6 months
- 【Transport】Temperature: -25~70°C; Max transport time: 10 days
- 【Unpack】Temperature: 20°C±5°C; Humidity: 50%RH±5%RH; Max storage time: Should be assembled in 72h
2、 What do you need to note about e-Paper refreshing
- Refresh mode
- Full refresh: e-Paper flicker when full refreshing to remove ghost image for best display.
- Partial refresh: It doesn't flicker if you use partial refresh (only some of the two-color e-paper support partial refresh). Note that you cannot use Partial refresh all the time, you should full refresh e-paper regularly, otherwise, ghost problem will get worse even damage
- Refresh rate
- When using, you should set the update interval at least 180s. (except Partial supportable types)
- Please set the e-Paper to sleep mode or power off it directly, otherwise, the e-Paper is damaged because of working in high voltage for a long time.
- You need to update the content of three-color e-Paper at least one time every 24h to avoid the burn-in problem.
- Working place
- We recommend you to use the e-Paper indoor. If you need to set the e-paper outdoor, Please place the e-paper in shadow and protect it from UV. When you designed you e-paper product, you should take care about the working situation like temperature, humidity, etc.
3、Why the e-Paper display a black frame？
- You can configure Border Waveform Control register or VCOM AND DATA INTERVAL SETTING register to change the frame.
4、Could the e-Paper work again after sleeping？
- You can use the initial function to wake it up and then update.
